How to install mac os x lion on pc with windows 8

This will search your Mac for the Disk Utility app. Click Disk Utility. It's below the Spotlight search bar. Doing so will open Disk Utility. Select your USB drive. Click the USB drive's name in the upper-left side of the window. Click the Erase tab. It's near the top of the window.

A pop-up box will appear. Click the "Format" drop-down box. You'll find this in the middle of the pop-up box. Clicking it prompts a drop-down menu. This will set your USB drive's file system to that of your Mac. Click the "Scheme" drop-down box. It's below the "Format" drop-down box. This option is in the "Format" drop-down menu. Click Erase. Doing so will reformat your USB drive to your Mac's file system. Click Done when prompted.

You can now proceed with creating your installation drive. Open the Unibeast folder. Double-click the Unibeast folder to unzip and open it. Click Open when prompted. Doing so will open the Unibeast setup window.

How to Access Your Mac Data From a Windows 8 PC

If your Mac is currently running macOS Sierra or higher, you'll have to verify the Unibeast installation before continuing. Click Continue four times. It's in the bottom-right corner of the first four pages of the Unibeast setup window. Click Agree when prompted. It's at the top of the window. Select your USB drive, then click Continue. Click the USB drive's name to select it. Select High Sierra , then click Continue.

You should see High Sierra in the middle of the page. Select a motherboard type. Select a graphics card option if necessary, then click Continue. Check the box next to Inject [card name] for your preferred graphics card settings. If your graphics card supports macOS High Sierra by default, skip this step. Click Continue. It's in the bottom-right corner of the page. Doing so will prompt you to enter your Mac's password.

Enter your Mac's password. Type in the password you use to log into your Mac.


  • finding ip address on mac network?
  • chrome temporary files mac os x?
  • How to Run Mac OS X Inside Windows Using VirtualBox.
  • Hackintosh Mojave Enable Hardware Acceleration.
  • mac os screenshot not working.
  • How To Install Windows 10/8 On Mac.

Click OK. This will prompt Unibeast to begin installing to the USB drive. While the Unibeast installation finishes up, you should change your Windows computer's boot order.

Unplug any USB items from your Windows computer. Make sure that you don't have any USB drives, in particular. This process varies from computer to computer, but you will typically restart your computer and then repeatedly press a key e. Locate the "Boot Order" section. This section is normally on the main page of the BIOS, though you may need to use the arrow keys to navigate over to the "Boot" or "Advanced" tab. Select Removable Devices. Use the arrow keys to move the blinking bar down to Removable Devices.


  • Categories;
  • how to download warface on mac.
  • driver canon lide 110 mac 10.8.

On some pages, this section may instead be called USB Devices or something similar e. Move your selected location to the top of the list. You can double-check the key that you're supposed to use in the legend that's usually on the right side or the bottom of the BIOS page. Save your settings and exit the BIOS. Look for the key you're supposed to press to save and exit in the legend on the right side of the page, then press it. Doing so will shift your Windows computer's boot priority so that installation USB drive will be selected as the boot point once you plug it in. You may have to press another key to confirm this choice.

Place Multibeast on the USB drive.

Step 1: Requirements

Open the USB drive's folder, then drag the Multibeast file into the folder. You'll need to use Multibeast later, so having it on the flash drive will make using it when necessary as simple as possible. After doing so, you can remove your USB drive. You should make sure that the Unibeast installation is complete before doing this.

Shut down your Windows computer. Press and hold the Power button on your Windows computer until your computer shuts down completely. This will usually occur one or two seconds after the computer's display turns off.

Install Mac OS X Lion on Non-Brand PC

Plug both the Unibeast USB drive and the blank hard drive into your computer. These should both fit into USB ports on your computer. Start your Windows computer. Press the Power button to start the computer. Once the computer has a chance to begin booting, it should select your plugged-in USB drive as a place from which to boot. This will begin the macOS installation process. Doing so takes you to the next page of the installer. Click Continue twice. It's in the bottom-right corner of the pages.

You'll see this at the top of the screen. Click the Utilities menu item. This menu item is in the top-left side of the screen. A drop-down menu will appear. It's in the drop-down menu. Select the blank hard drive. Click the blank hard drive's name on the left side of the page.

Setting up BIOS on Non-Brand PC

It's near the top of the page. Format the blank hard drive. Doing so will reformat your blank hard drive for macOS' file system. Click Done when prompted, then close the Disk Utility window. You can now proceed with installing macOS High Sierra on the hard drive. Click the blank hard drive's name, then click Continue. This will both select the hard drive as the installation point and begin installing macOS High Sierra.

Wait for macOS High Sierra to finish installing. This process should take around 15 minutes. Follow the on-screen prompts. You'll be prompted to enter specific information, such as your name, a password, your preferred language, your location, and so on. Once you complete this setup process, macOS' software will be completely set up on your Windows computer. Open your flash drive. Double-click the Multibeast file. Doing so will open the Multibeast window. Click the Bootloaders tab.

Select the proper bootloader. Click the Drivers tab. You'll find this option at the top of the window. Click Audio. It's on the left side of the window. Select audio drivers. Click the current audio item's heading in the middle of the window to expand it, then check the box next to your computer's audio provider's name.

Click Misc. This option is on the left side of the window. Check the "FakeSMC" box. You'll find it near the top of the window. Click Network. Select an Internet driver. Click the name of your Internet card, then check the box next to the driver's name. Click the Customize tab. Select the proper graphics options. Check the box next to your computer's graphics card name, then check the "Fixup" box for your graphics card's manufacturer. Leave the "Inject" options blank. Click System Definitions. Select a Mac which most closely resembles your computer. Click the heading of the type of Mac e.

Click the Build tab. Requires Personal Hotspot service through your carrier.

How to install Windows 8 on a Mac

Supported by the following Mac models:. Installing the latest Service Packs is recommended. Upgrade now. Upgrading is free.

Hackintosh Instructions, Hackintosh How To Guides: nabahulelixa.gq

General Requirements. Mac Hardware Requirements. Feature Requirements. Siri Requires a broadband Internet connection and microphone built-in or external. Spotlight Suggestions Requires a broadband Internet connection. Force Touch gestures require a Force Touch trackpad. FaceTime Audio calls require a microphone built-in or external and broadband Internet connection.


healthrenorsforra.cf/romancing-the-slut-sexy-erotica.php admin